ProSoft MVI56-ADM Application Development Module

Contact: Nancy Lin
Email:*
Skype:onlywnn_1
Telegram:+8618020776786
Mobile(Whatsapp): (+86)-18020776786
QQ :2851195456

Our company has many products in stock,which are immediately available.The warranty is 1 years which apply to all the new products.If you purchase one more parts from us,we can make a discount to you.
If you have any question pls do not hesitate to contact us.We can supply all kind of the automaiton parts,if you want to purchase parts pls send the parts model to my mail, I will prompt reply you as I receive the mail * .
Hope anyone enquire from us.
We have a large inventory of control system components. We also made a lot of new hardware and discontinued spare parts to help supporting your existing control systems.
We have experienced staff, extensive testing , all the spare parts which we sold are with warranty period of one year, and they have undergone rigorous testing and certification!
You might find you need spare parts in our data, we welcome you give valuable suggestions to us with our products at any time.

1.Q:What about your shipping terms ?
A: We can ship by DHL,UPS,FEDEX,ARAMAX,TNT,and so on


2.We're in this field more than 12 years. If there's any problem, please contact with us,we'll provide suggestion from our engineer to help you solve problem.

3.Q:How long warranty does Amikon can provide ?
A: 1 year warranty !



Set the PRT 2 (for application port 1) and PRT 3 (for application port 2)
jumpers for RS232, RS422 or RS485 to match the wiring needed for your
application. The default jumper setting for both application ports is RS-232.
2 The Setup Jumper acts as "write protection" for the module's flash memory.
In "write protected" mode, the Setup pins are not connected, and the
module's firmware cannot be overwritten. Do not jumper the Setup pins
together unless you are directed to do so by ProSoft Technical Support.

Install the Module in the Rack
If you have not already installed and configured your ControlLogix processor and
power supply, please do so before installing the MVI56-MDA4 module. Refer to
your Rockwell Automation product documentation for installation instructions.
Warning: You must follow all safety instructions when installing this or any other electronic
devices. Failure to follow safety procedures could result in damage to hardware or data, or even
serious injury or death to personnel. Refer to the documentation for each device you plan to
connect to verify that suitable safety procedures are in place before installing or servicing the
device.


After you have checked the placement of the jumpers, insert MVI56-MDA4 into
the ControlLogix chassis. Use the same technique recommended by Rockwell
Automation to remove and install ControlLogix modules.
Warning: When you insert or remove the module while backplane power is on, an electrical arc
can occur. This could cause an explosion in hazardous location installations. Verify that power is
removed or the area is non-hazardous before proceeding. Repeated electrical arcing causes
excessive wear to contacts on both the module and its mating connector. Worn contacts may
create electrical resistance that can affect module operation.
1 Turn power OFF.
2 Align the module with the top and bottom guides, and slide it into the rack
until the module is firmly against the backplane connector.


AB 1785-L40L
AB 1785-L60L
AB 1785-L86B
AB 1771-DRS1
AB 1785-ME16
AB 1785-BEM
AB 1771-ALXK
AB 1771-A1BK
AB 1771-A3B1K
AB 1771-AM2
AB 1771-IADK
AB 1771-IBN
AB 1771-ID
AB 1771-IDK
AB 1771-IM
AB 1771-INGA50
AB 1771-IT
AB 1771-OAN
AB 1771-OBDSK
AB 1771-OD



AB 1771-ODDK
AB 1771-OGD
AB 1771-OP
AB 1771-OR
AB 1771-OWK
AB 1771-OYL
AB 1771-IFE
AB 1771-IXEK