GT-100 GSM Terminal Use As Backup For PSTN in The Alarm System and Gate Controller.

GSM Terminal Use As Backup For PSTN in The Alarm System and Gate Controller.

The new GT-100 GSM Terminal is a wireless communicator for alarm, fire panels that uses the cell phone network (GSM) to transmit alarm and other panel event. the module check the status of the PSTN line and in case the PSTN line become unavailble, the GT-100 GSM emulate the line signal to the panel. at this time, the panel will dial out using the GSM cell phone network to communicate with the receive at the CMS station and transmit the reports.GT-100 offer a number of solutions to open gates by a simple phone call. Just dial a number to open your gates. GT-100 User List of numbers who are enabled to open the phone, up to 100.


Features:

-Allows any contact ID alarm to transmit alarms over GSM using the GSM voice Channel.

-Work over the GSM cell phone networks units can be used wherever there is cell phone coverage.

-GT-100 offer a number of solutions to open gates by a simple phone call. Just dial a number to open your gates.

-GT-100 User List of numbers who are enabled to open the phone, up to 100.

-GT-100 uses the telephone line as the main transmission line and uses the GSM Voice channel as backup.

-GT-100 has built-in alarm inputs that allow the unit to send additional signals to CMS monitoring station.

-Three open collector outputs (that can sink max 300ma per output) can be turned on and off remotely through a sms or phone call.

-Programmable cell phone number to notify the user that the PSTN line has been cut off or unavailable.

Function:

Programmable 5 Administrator/CMS Number
Programmable Recipient that will receive Alert Messages
Programmable Area Code
Programmable the dialing Time Number
Programmable Clock Setting
Programmable Account Number for CMS
Programmable Auto Test Report Time Section up to 3 Sections
Programmable sending Reports to CMS
Programmable generation of sms report for auto test
Programmable for PSTN send sms Failure
Programmable for PSTN sending report to CMS (Failure) and connected
Programmable for AC Failure sending report to CMS or SMS to admin
Programmable Enable/Disable System Power Up SMS Notification
Programmable Ignore the front dialing digits when dialing the Administrator or CMS number
Programmable Editing the Inputs Alert Messages (detecting 5~12VDC triggered)
Programmable Editing the Input Alert Message For (detecting 0 VDC triggered)
Programmable Editing the Outputs (Open) Alert Messages
Programmable Editing the Outputs (Closed) Alert Messages
Programmable Activate Output to Stay On for a Specific Time
Programmable Activate the Output Relay to Stay On
Programmable Setup User List to trip the output 1,2,3 via SMS
Programmable Output Pulse time via SMS
Programmable Reset to factory default via SMS
Programmable Checking the Signal Strength via SMS
Programmable Inquire the Software, Hardware Version and serial number of GT-100 Terminal via SMS
Programmable Inquire the All Status
Programmable Checking the Current Time Status via SMS



Main Features of the GT-100:

Telephone line backup:GT-100 give priority to the lowest cost network. GT-100 uses the telephone line as the main transmission line and uses the GSM voice channel as backup

GT-100 offers a number of solutions to open gates by a simple phone call. Just dial a number to open your gates. User List of numbers who are enabled to open the phone, up to 100.

Programmable Account Number: The GT-100 has built-in alarm inputs that allow the unit to send additional signals (with user programmable Account number) to the monitoring station. The Alarm Events that available in this system are PSTN Failure, AC Failure and Auto Test. Supported Protocol: Pager message (DTMF with handshake)

Sends text messages to user programmable cell phone number (SMS): The GT-100 can be programmed to send a SMS to a programmable cell phone number to notify the user that the PSTN line has been cut off or unavailable.

Three digital inputs: The system has the function to send SMS and call to the user in the event of input triggered. For example, Input 3 connected to an electric door, when there is intruder or the electric door is open illegally, GT-100 will receive short circuit impulse on Input 3 and automatically sends a signal to the pre-set number and notify the owner.

Three remote control outputs: These open collector outputs (that can sink max 300ma per output) can be turned on and off remotely through a SMS or phone call. Remote control will be reachable by sending a SMS or phone call with a certain command. For example SMS/Call in to switch on lighting, air conditional, generator, sensor or other equipment.

Standby rechargeable battery to prevent power failure or electricity cut off by intruder. The GSM will function as normal when no electricity supply. LED to check the GSM signal strength.

Low power consumption – uses 30mA while in idle state and 260mA when transmitting an alarm

*